SainSmart 8-Channel 5V Solid State Relay Module Board for Arduino Uno Duemilanove MEGA2560 MEGA1280 ARM DSP PIC Review

SainSmart 8-Channel 5V Solid State Relay Module Board for Arduino Uno Duemilanove MEGA2560 MEGA1280 ARM DSP PIC Feature

• Has been assembled, and electrical test passed.
• Led indicator for each relay.
• FR-4 Fiber glass PCB ( Double Layer ).
• PCB thickness: 1.6mm. Size: 155 x 55 x 24 mm ( approximately 6.1 x 2.17 x 0.95 inch ).
• Standard interface that can be controlled directly by microcontroller (Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic)

SainSmart 8-Channel 5V Solid State Relay Module Board for Arduino Uno Duemilanove MEGA2560 MEGA1280 ARM DSP PIC Overview

NOTE:The link is the schematic about SainSmart 8-Channel 5V Solid State Relay Module Board.

https://s3-ap-northeast-1.amazonaws.com/sain-amzn/20/20-018-200/8+solid+relay.rar

 

SSR Output (each channel):
Load voltage range: 75 to 264VAC (50/60Hz).
Load current: 0.1 to 2 AMP.

Power supply:
5VDC / 160mA (all channel ON).

Input control signal voltage:
0V - 0.5V Low stage (SSR is OFF)
0.5V - 2.5V (unknown state).
2.5V - 20V High state (SSR is ON).

SSR Spec.:
Manufacturer: OMRON
Part number: G3MB-202P, 5V version.
Isolation: Phototriac.
Zero cross: Yes.
Rated output load: 2A at 100 to 240VAC.(50/60Hz).
Load type: General purpose.

Available at Amazon

Related Products

• SainSmart 4-Channel 5V Relay Module for Arduino DSP AVR PIC ARM
• SainSmart 8-Channel 5V Relay Module for Arduino DSP AVR PIC ARM
• Arduino Uno R3
• Wall Adapter Power Supply - 9VDC 650mA
• Ultrasonic Module HC-SR04 Distance Sensor For Arduino

Customer Reviews

*** Product Information and Prices Stored: May 31, 2012 04:45:11

RGB LCD Shield for Arduino 65K color KIT Review

RGB LCD Shield for Arduino 65K color KIT Feature

• Passive Matrix Liquid Crystal Display Panel,transflective, 65536 colours, negative mode
• Display Resolution: 128 x 128
• Backlight: white LED - 15V (Max) - 9V (Nominal) - 19mA
• Interface: 4-wire serial

RGB LCD Shield for Arduino 65K color KIT Overview

RGB LCD 65K color shield kit for Arduino. All components included, PCB, LCD module, regulator, discrete components.Instructions: http://mcukits.com/2011/01/02/rgb-lcd-shield-for-arduino-65k-color-kit-v2-assembly-guide/

Available at Amazon

Related Products

• Arduino Uno R3
• Wall Adapter Power Supply - 9VDC 650mA
• Ultrasonic Module HC-SR04 Distance Sensor For Arduino
• Box for Arduino
• Elenco 100 Capacitor Component Kit

Customer Reviews

*** Product Information and Prices Stored: May 29, 2012 23:45:11

SainSmart 8 channel Signal Relay for Arduino UNO R3 MEGA2560 MEGA1280 Review

SainSmart 8 channel Signal Relay for Arduino UNO R3 MEGA2560 MEGA1280 Overview

NOTE:The link is the documents about SainSmart 8 channel Signal Relay.

https://s3-ap-northeast-1.amazonaws.com/sain-amzn/20/20-018-906/8+signal.rar

Available at Amazon

Related Products

Customer Reviews

*** Product Information and Prices Stored: May 26, 2012 19:45:06

SainSmart MEGA, ATmega2560 + SainSmart LCD Keypad Shield + SainSmart Prototype Shield(with Breadboard Jump Wires) for Arduino Review

SainSmart MEGA, ATmega2560 + SainSmart LCD Keypad Shield + SainSmart Prototype Shield(with Breadboard Jump Wires) for Arduino Feature

• The SainSmart Arduino MEGA, ATmega2560 is a microcontroller board based on the ATmega2560.
• The SainSmart LCD Keypad shield module for Arduino Diecimila Duemilanove, UNO, MEGA1280, MEGA2560 board.
• SainSmart Prototype Shield: Access to a BlueSMiRF socket for wireless communication between Arduinos
• Buy them TOGETHER and get at the REDUCE price. It is a big bargain!!!

SainSmart MEGA, ATmega2560 + SainSmart LCD Keypad Shield + SainSmart Prototype Shield(with Breadboard Jump Wires) for Arduino Overview

NOTE:The link is the instructions about keypad shield.

https://s3-ap-northeast-1.amazonaws.com/sain-amzn/20/20-011-901/LCD1602.rar

The SainSmart MEGA 2560 Board for Arduino: This is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.

The SainSmart LCD Keypad Shield includes a 16x2 HD44780 White on Blue LCD module and a 5 push button keypad for menu selection and user interface programming. Fully assembled. On-line Arduino tutorial and example code. Compatible with Arduino Uno, Mega, Duemilanove. Uses digital pins 4 - 10, and analog pin 0.

The SainSmart Prototyping Prototype Shield is a great kit to new Arduino users and geeks who have sparkling ideas. You can choose to do soldering in the soldering area. You can also make good use of the mini breadboard which can save your time of soldering. Try any circuit you want to the Arduino. You also can choose to use your own breadboard.

Package Content:
1 SainSmart MEGA 2560 Board
1 SainSmart LCD Keypad Shield
1 SainSmart Prototype Shield
1 Mini Breadboard
65*Jumper Cable

Available at Amazon

Related Products

• Arduino UNO board
• Elenco 350 Piece Pre-formed Jumper Wire Kit
• LCD Module for Arduino 20 x 4, White on Blue

Customer Reviews

*** Product Information and Prices Stored: May 25, 2012 16:15:06

SainSmart 2 channel Signal Relay for Arduino UNO R3 MEGA2560 MEGA1280 Review

SainSmart 2 channel Signal Relay for Arduino UNO R3 MEGA2560 MEGA1280 Overview

NOTE:The link is the documents about SainSmart 2 channel Signal Relay.

https://s3-ap-northeast-1.amazonaws.com/sain-amzn/20/20-018-904/2+signal.rar

Interface definition:
IN(x): High level. Low level cut-off
This item has been assembled,
Led indicator for each relay.

FR-4 Fiber glass PCB ( Double Layer ).
PCB thickness: 1.6mm.
Size: 54 x 46 x 16 mm .

Power Supply: 5V DC / 40mA (relay all ON).

Input control signal voltage:
0V - 0.5V Low stage (relay is OFF),
0.5V - 2.5V (unknown state).
2.5V - 5V High state (relay is ON).
Input control signal high state current:
2.5V: 0.1mA
3.3V: 0.18mA
5V: 0.35mA


Relay Spec:
Coil:
Voltage: 5V DC.
Current: 8.3mA.
Resistance: 2880 ohm +-10%.
Contact Rating:

Contact Resistance: <0.1 ohm.
Contact Capacity: 125V AC / 1A, 30V DC / 2 A.

Available at Amazon

Related Products

Customer Reviews

*** Product Information and Prices Stored: May 24, 2012 11:30:08

SainSmart L293D Motor Drive Shield For Arduino Duemilanove Mega UNO R3 AVR ATMEL Review

SainSmart L293D Motor Drive Shield For Arduino Duemilanove Mega UNO R3 AVR ATMEL Feature

• Brand new and high quality
• Size:6.8cm x 5.5cm x 2cm - 2.68inch x 2.17inch x 0.79inch.

SainSmart L293D Motor Drive Shield For Arduino Duemilanove Mega UNO R3 AVR ATMEL Overview

Features:

L293D is a monolithic integrated, high voltage, high current, 4-channel driver.
Basically this means using this chip you can use DC motors and power supplies of up to 36 Volts, thats some pretty big motors and the chip can supply a maximum current of 600mA per channel, the L293D chip is also what's known as a type of H-Bridge.

The H-Bridge is typically an electrical circuit that enables a voltage to be applied across a load in either direction to an output, e.g. motor.

2 interface for 5V Servo connected to the Arduino's high-resolution dedicated timer - no jitter.
Can drive 4 DC motors or 2 stepper motors or 2 Servo.
Up to 4 bi-directional DC motors with individual 8-bit speed selection.
Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping.
4 H-Bridges: per bridge provides 0.6A (1.2A peak current) with thermal protection, can run motors on 4.5V to 36V DC.
Pull down resistors keep motors disabled during power-up.
reset button.
2 external terminal power interface, for seperate logic/motor supplies.
Tested compatible for Arduino Mega, Diecimila & Duemilanove.

Available at Amazon

Related Products

Customer Reviews

*** Product Information and Prices Stored: May 23, 2012 09:45:10

Arduino Ethernet Shield R2 with PoE module Review

Arduino Ethernet Shield R2 with PoE module Feature

• Ethernet Shield for Arduino R2 with PoE module
• Develop TCP/IP enabled client and server applications on your Arduino board
• Freeduino / Seeeduino compatible
• micro-SD socket (with active voltage translator) and reset switch (on board reset controller)
• Arduino MEGA compatible

Arduino Ethernet Shield R2 with PoE module Overview

The Arduino Ethernet shield allows an Arduino board to connect to a LAN using the Ethernet library. New version with micro-SD socket, reset switch and compatible with Arduino MEGA. This is the R2 board, with PoE module pre-installed.

Available at Amazon

Related Products

Customer Reviews

*** Product Information and Prices Stored: May 22, 2012 09:15:08

SainSmart Sensor Shield Digital Analog Module V5 for Arduino UNO MEGA Duemilanove Review

SainSmart Sensor Shield Digital Analog Module V5 for Arduino UNO MEGA Duemilanove Feature

• Buckled Analog Port:Handy, solid connection to 6 Analog inputs with VCC/GND
• Digital IO port:13 ports prepared to digital modules or servos
• Analog IO Port:2.54 grid male pin header connections
• Buckled Communication Port:Selectable between I2C and UART

SainSmart Sensor Shield Digital Analog Module V5 for Arduino UNO MEGA Duemilanove Overview

The SainSmart Sensor Shield V5 (new version) has the COM and I2C (IIC) ports separated,so that both ports can be utilized at the same time to increase the possibilities of use.

Arduino Sensor Shield allows you to connect to various modules like sensors, servos, relays, buttons, potentiometers and so on.Just plug & play.Each functional module has buckled port with VCC, GND and Output, which has corresponding port on the Sensor Shield, connected with a plain 2.54mm dual-female cable you may start playing already. Buckled brick cables are like cement for bricks, make the connections easier, securer and more professional.

Available at Amazon

Related Products

• SainSmart 4-Channel 5V Relay Module for Arduino DSP AVR PIC ARM
• Arduino Uno R3
• Wall Adapter Power Supply - 9VDC 650mA
• Ultrasonic Module HC-SR04 Distance Sensor For Arduino
• SainSmart LCD Keypad Shield for Arduino UNO MEGA Duemilanove

Customer Reviews

*** Product Information and Prices Stored: May 21, 2012 08:45:12

Wall Adapter Power Supply - 9VDC 650mA Review

Wall Adapter Power Supply - 9VDC 650mA Feature

• AC to DC power supply
• 9V 650mA,110 - 240V AC input
• 5.5 x 2.1 mm Plug center positive

Wall Adapter Power Supply - 9VDC 650mA Overview

High quality switching 'wall wart' AC to DC 9V 650mA wall power supply

Available at Amazon

Related Products

• Arduino Uno R3
• Arduino Uno Rev 3 Starter Kit -- 3' USB Cable --Solderless Breadboard -- 65 Jumper Wires -- Breadboard Holder
• Breadboard jumper wire 70pcs pack
• 30 Arduino Projects for the Evil Genius
• Box for Arduino

Customer Reviews

*** Product Information and Prices Stored: May 20, 2012 08:30:14

Arduino Ethernet Shield W5100 Review

Arduino Ethernet Shield W5100 Feature

• Arduino ethernet shield based on the Wiznet W5100 ethernet chip.

Arduino Ethernet Shield W5100 Overview

This is an Ethernet shield based on the Wiznet W5100 ethernet chip. It supports Arduino, including the Arduino Mega. (To use with Arduino Mega, please download updated Ethernet Library from SeeedStudio.)

Available at Amazon

Related Products

Customer Reviews

*** Product Information and Prices Stored: May 19, 2012 07:15:12

Arduino Ethernet with Power-over-Ethernet (PoE) Module Review

Arduino Ethernet with Power-over-Ethernet (PoE) Module Feature

• Includes Power-over-Ethernet (PoE) Module
• Includes a handy Cana Kit General Assembly Guide

Arduino Ethernet with Power-over-Ethernet (PoE) Module Overview

IMPORTANT NOTE:

There have been reports that this board does not work consistently with some FTDI based USB to Serial Converters. We are working with Arduino to identify the root cause of the problem, but in the meantime it is highly recommended that you order the Arduino USB to Serial Converter in order to be able reliably program this board. The Arduino USB to Serial Converter is available on Amazon under ASIN B005G89KT8.

The Arduino Ethernet is a microcontroller board based on the Arduino Uno incorporating a WizNet W5100 TCP/IP Embedded Ethernet Controller. It can be programmed like an Uno via a six-pin serial connector. The Arduino USB-to-Serial adapter can be used to program it.

A separate power-over-Ethernet (PoE) module is soldered to the board to provide power from a conventional twisted pair Category 5 Ethernet cable. It is IEEE802.3af compliant, and works with all compliant PoE injectors currently available.

Available at Amazon

Related Products

• Arduino Ethernet Shield
• Arduino UNO board
• Arduino USB to Serial Converter / Adapter Board
• Box for Arduino
• Elenco 365 Piece Resistor Kit

Customer Reviews

*** Product Information and Prices Stored: May 18, 2012 07:00:15

Arduino Ethernet Shield R3 with PoE module Review

Arduino Ethernet Shield R3 with PoE module Feature

• Ethernet Shield for Arduino R3 with PoE module
• Develop TCP/IP enabled client and server applications on your Arduino board
• Freeduino / Seeeduino compatible
• micro-SD socket (with active voltage translator) and reset switch (on board reset controller)
• Arduino Mega compatible

Arduino Ethernet Shield R3 with PoE module Overview

The Arduino Ethernet Shield (R3) allows an Arduino board to connect to a LAN using the Ethernet library. New R3 version with micro-SD socket, reset switch and compatible with Arduino Mega. This is the R3 board, with PoE module pre-installed.

Available at Amazon

Related Products

Customer Reviews

*** Product Information and Prices Stored: May 17, 2012 06:45:09

Arduino Ethernet Shield w/o PoE Module Review

Arduino Ethernet Shield w/o PoE Module Feature

• The Arduino Ethernet Shield allows an Arduino board to connect to the Internet.

Arduino Ethernet Shield w/o PoE Module Overview

The Arduino Ethernet Shield allows an Arduino board to connect to the Internet.

Available at Amazon

Related Products

Customer Reviews

*** Product Information and Prices Stored: May 16, 2012 06:30:13

Arduino Duemilanove Review

Arduino Duemilanove Feature

• Arduino Board with ATmega328 microcontroller
• Original board made in Italy

Arduino Duemilanove Overview

Arduino Duemilanove Board with ATmega328 Microcontroller

Available at Amazon

Related Products

• Wall Adapter Power Supply - 9VDC 650mA
• BB400 Solderless Plug-in BreadBoard, 400 tie-points, 4 power rails, 3.3 x 2.1 x 0.3in (84 x 54 x 9mm)
• Box for Arduino
• Breadboard jumper wire 70pcs pack
• Elenco 350 Piece Pre-formed Jumper Wire Kit

Customer Reviews

*** Product Information and Prices Stored: May 15, 2012 04:15:10

HC-SR04, Ultrasonic, Distance Sensor+SainSmart LCD Keypad Shield Review

HC-SR04, Ultrasonic, Distance Sensor+SainSmart LCD Keypad Shield Feature

• Ultrasonic Module HC-SR04 Distance Sensor automatically sends eight 40 kHz and detect whether there is a pulse signal back
• The SainSmart LCD Keypad shield module for Arduino Diecimila Duemilanove, UNO, MEGA1280, MEGA2560 board.
• Buy them TOGETHER and get at the REDUCE price. It is a big bargain!!!

HC-SR04, Ultrasonic, Distance Sensor+SainSmart LCD Keypad Shield Overview

NOTE:The link is the instructions about keypad shield.

https://s3-ap-northeast-1.amazonaws.com/sain-amzn/20/20-011-901/LCD1602.rar


The SainSmart LCD Keypad Shield includes a 16x2 HD44780 White on Blue LCD module and a 5 push button keypad for menu selection and user interface programming. Fully assembled. On-line Arduino tutorial and example code. Compatible with Arduino Uno, Mega, Duemilanove. Uses digital pins 4 - 10, and analog pin 0.

The Ultrasonic Module HC-SR04 Distance Sensor are 4 pins out of the module: VCC, Trig, Echo, GND. So it's a very easy interface for controller to use it ranging. The all process is : pull the Trig pin to high level for more than 10us impulse, the module start ranging; finish ranging, If you find an object in front, Echo pin will be high level, and based on the different distance,it will take the different duration of high level. So we can calculated the distance easily:

Distance = ((Duration of high level)*(Sonic :340m/s))/2

Package Content:
1 SainSmart LCD Keypad Shield
1 Ultrasonic Module HC-SR04 Distance Sensor

Available at Amazon

Related Products

• Wall Adapter Power Supply - 9VDC 650mA
• Arduino Uno Rev 3 Starter Kit -- 3' USB Cable --Solderless Breadboard -- 65 Jumper Wires -- Breadboard Holder

Customer Reviews

*** Product Information and Prices Stored: May 14, 2012 01:45:06

Electronic Parts for Getting Started With Arduino book (BOOK NOT INCLUDED) Review

Electronic Parts for Getting Started With Arduino book (BOOK NOT INCLUDED) Feature

• Getting Started with Arduino book parts kit
• Includes 70-pcs jumper wires

Electronic Parts for Getting Started With Arduino book (BOOK NOT INCLUDED) Overview

This pack contains the parts needed to try the exercises listed in the Getting Started with Arduino book. It includes a mini breadboard, LEDs, a DIODE, a TRANSISTOR, RESISTORS, a SWITCH, 70 jumper wires and LDR. It tries to match the components listed and used in the book. The resistors for the LEDs can have different values, 220 or 330 ohms.BOOK NOT INCLUDED

Available at Amazon

Related Products

• Arduino Uno Rev 3 Starter Kit -- 3' USB Cable --Solderless Breadboard -- 65 Jumper Wires -- Breadboard Holder
• Arduino Uno R3
• Wall Adapter Power Supply - 9VDC 650mA
• BB400 Solderless Plug-in BreadBoard, 400 tie-points, 4 power rails, 3.3 x 2.1 x 0.3in (84 x 54 x 9mm)
• Getting Started with Arduino

Customer Reviews

*** Product Information and Prices Stored: May 13, 2012 01:30:06

SainSmart MEGA, ATmega2560+ SainSmart Graphic LCD4884 Shield Review

SainSmart MEGA, ATmega2560+ SainSmart Graphic LCD4884 Shield Feature

• The SainSmart Arduino MEGA, ATmega2560 is a microcontroller board based on the ATmega2560.
• The SainSmart Graphic LCD4884 Shield has one 5 degree joystick (using Arduino Analog Pin 0)
• Buy them TOGETHER and get at the REDUCE price. It is a big bargain!!!

SainSmart MEGA, ATmega2560+ SainSmart Graphic LCD4884 Shield Overview

The link bellow is the code for the LCD4884. Please download it if you need it.
https://s3-ap-northeast-1.amazonaws.com/sain-amzn/20/20-011-906/LCD4884s.rar

The SainSmart MEGA 2560 Board for Arduino: This is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.


The SainSmart LCD4884 Shield provides 48x48 display. This LCD shield can apparently meet your needs to display much information. It can display English, Chinese, even images. It also integrates a 5 DOF joystick. The shield has 6 Digital IO and 5 Analog IO.This 3 pin connector has a temperature sensor which can help indicate the temperature.

Package Content:
1 SainSmart MEGA 2560 Board
1 SainSmart LCD4884 Shield

Available at Amazon

Related Products

Customer Reviews

*** Product Information and Prices Stored: May 11, 2012 23:15:08

Netduino Plus Review

Netduino Plus Feature

• The Netduino Plus is an open source electronics platform using the .NET Micro Framework.

Netduino Plus Overview

Netduino is an open source electronics platform using the .NET Micro Framework.Featuring a 32-bit microcontroller and a rich development environment.Suitable for engineers and hobbyists alike.Input. Output.Interface with switches, sensors, LEDs, serial devices, and more. Netduino offers 20 GPIOs combined with SPI, I2C, 2 UARTs (1 RTS/CTS), 4 PWM channels and 6 ADC channels.Code. Debug. Repeat..NET Micro Framework combines the ease of high-level coding and the raw features of microcontrollers. Enjoy event-based programming, multi-threading, line-by-line debugging, breakpoints and more.Very expandable.3rd-party accessories offer pre-built functionality like GPS location, servo control and battery power. Netduino is also pin-compatible with Arduino shields. 3rd-party drivers are required for some Arduino shields.Design files included.Netduino is an open source electronics platform. All design files and source code are included. Learn from the designs. Remix. Enjoy the freedom of open source.Netduino Plus includes all hardware features of the Netduino--plus MicroSD storage capabilities and an Ethernet jack for fast integrated IP networking.

Available at Amazon

Related Products

• Wall Adapter Power Supply - 9VDC 650mA
• Breadboard jumper wire 70pcs pack
• Getting Started with the Internet of Things: Connecting Sensors and Microcontrollers to the Cloud (Make: Projects)
• Getting Started with Netduino
• Getting Started with the Internet of Things: Connecting Sensors and Microcontrollers to the Cloud (Make: Projects)

Customer Reviews

*** Product Information and Prices Stored: May 10, 2012 22:45:09

Arduino Uno Rev 3 Starter Kit -- 3' USB Cable --Solderless Breadboard -- 65 Jumper Wires -- Breadboard Holder Review

Arduino Uno Rev 3 Starter Kit -- 3' USB Cable --Solderless Breadboard -- 65 Jumper Wires -- Breadboard Holder Feature

• Arduino Uno Rev 3-- 16MHz ATmega 328
• Breadboard --- 400 tie points total: 300 tie-point IC-circuit area plus two 50 tie-point distribution strips providing 4 power rails.
• Jumper Wires -- 65 pcs of 22 AWG jumper wire ,100mm 45pcs
• 3' USB Cable for the arduino Uno
• Bread Board + Arduino Holder -- Perfect fit holder to keep your Arduino Uno Rev 3

Arduino Uno Rev 3 Starter Kit -- 3' USB Cable --Solderless Breadboard -- 65 Jumper Wires -- Breadboard Holder Overview

OverviewThe Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.


The Uno differs from all preceding boards in that it does not use the FTDI USB-to-serial driver chip. Instead, it features the Atmega8U2 programmed as a USB-to-serial converter.

Available at Amazon

Related Products

• Wall Adapter Power Supply - 9VDC 650mA
• 30 Arduino Projects for the Evil Genius
• Programming Arduino Getting Started with Sketches
• microtivity LCD Module 1602, White on Blue with Backlight
• 5mm Assorted LED w/ Resistors (5 Colors, Pack of 25)

Customer Reviews

*** Product Information and Prices Stored: May 09, 2012 22:00:11

SainSmart IIC/I2C/TWI Serial 2004 20x4 LCD Module Shield For Arduino UNO MEGA R3 Review

SainSmart IIC/I2C/TWI Serial 2004 20x4 LCD Module Shield For Arduino UNO MEGA R3 Feature

• 2012 latest IIC LCD2004-character LCD display module

SainSmart IIC/I2C/TWI Serial 2004 20x4 LCD Module Shield For Arduino UNO MEGA R3 Overview

Description :

2012 latest IIC LCD2004-character LCD display module, a new high-quality 4 line 20 character LCD module not only set the contrast control knob selector switch also has a backlight and IIC communication interface. For Arduino beginners, not for the cumbersome and complex LCD driver circuit connection and a headache, the real significance of this LCD module will simplify the circuit, this module directly into the Arduino Sensor Shield V5.0 sensor expansion board IIC device interface can, GM 4P sensor connection cable, programmed through the Arduino controller, you can easily identify the slogan, sensor data records.

Specification:
Interface: I2C
I2C Address: 0x27
Pin Definition : GND?VCC?SDA?SCL
Back lit (Blue with White char color)
Supply voltage: 5V
Pcb Size : 60mmx99mm
Contrast Adjust : Potentiometer
Backlight Adjust : Jumper

Available at Amazon

Related Products

Customer Reviews

*** Product Information and Prices Stored: May 08, 2012 21:15:09

SainSmart Arduino MEGA, ATmega2560 + SainSmart Sensor Shield V4 + SainSmart XBee Shield + SainSmart LCD Keypad Shield Review

SainSmart Arduino MEGA, ATmega2560 + SainSmart Sensor Shield V4 + SainSmart XBee Shield + SainSmart LCD Keypad Shield Feature

• The SainSmart LCD Keypad shield module for Arduino Diecimila Duemilanove, UNO, MEGA1280, MEGA2560 board
• The SainSmart sensor shield V4 can connect to various modules like sensors, servos, relays, buttons, potentiometers
• The SainSmart XBee Shield is a compliant solution designed to meet low-cost, low-power wireless sensor networks with special needs.
• Buy them TOGETHER and get at the REDUCE price. It is a big bargain!!!

SainSmart Arduino MEGA, ATmega2560 + SainSmart Sensor Shield V4 + SainSmart XBee Shield + SainSmart LCD Keypad Shield Overview

NOTE: The XBee shield does not include the XBee module. Please send e-mail to us for sch.pdf if you need one after your purchase.

The SainSmart MEGA 2560 Board for Arduino: This is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.

The SainSmart Sensor Shield V4.0 for Arduino: It allows you to connect to various modules like sensors, servos, relays, buttons, potentiometers.

The SainSmart LCD Keypad Shield for Arduino: It includes a 16x2 HD44780 White on Blue LCD module and a 5 push button keypad for menu selection and user interface programming. Fully assembled. On-line Arduino tutorial and example code. Compatible with Arduino Uno, Mega, Duemilanove. Uses digital pins 4 - 10, and analog pin 0.

The SainSmartArduino XBee board for Arduino: It allows to wireless communicate over a modified ZigBee protocol using the popular XBee module from Maxstream.

The module is easy to use, low power consumption, and the provision of critical data between devices reliable transmission. As the innovative design, XBee-PRO can be in the range 2-3 times beyond the standard ZigBee modules.The MaxStream's XBee (1 mW) Zigbee module is pin-compatible.

Package Content:
1 SainSmart MEGA 2560 Board
1 SainSmart Sensor Shield V4.0
1 SainSmart LCD Keypad shield
1 SainSmart XBee Shield

Available at Amazon

Related Products

• Breadboard jumper wire 70pcs pack
• Arduino Sidekick Basic Kit
• SainSmart 4-Channel 5V Relay Module for Arduino DSP AVR PIC ARM
• Ultrasonic Module HC-SR04 Distance Sensor For Arduino

Customer Reviews

*** Product Information and Prices Stored: May 07, 2012 18:00:09

SainSmart LCD Keypad Shield for Arduino UNO MEGA Duemilanove Review

SainSmart LCD Keypad Shield for Arduino UNO MEGA Duemilanove Feature

• Arduino shield includes an 16 x 2 white on Blue character LCD and a 5 push button keypad
• 4 Bit Arduino LCD Library
• Blue Backlight with white words, adjustable backlighting.
• Keypad allows user input and menu selection for custom Arduino application
• Compatible with Arduino Uno, Mega, Duemilanove

SainSmart LCD Keypad Shield for Arduino UNO MEGA Duemilanove Overview

NOTE:The link is the instructions about keypad shield.

https://s3-ap-northeast-1.amazonaws.com/sain-amzn/20/20-011-901/LCD1602.rar

LCD Keypad shield for Arduino: This SainSmart LCD Keypad Shield includes a 16x2 HD44780 White on Blue LCD module and a 5 push button keypad for menu selection and user interface programming. Fully assembled. On-line Arduino tutorial and example code. Compatible with Arduino Uno, Mega, Duemilanove. Uses digital pins 4 - 10, and analog pin 0.

Available at Amazon

Related Products

• Arduino Uno R3
• Wall Adapter Power Supply - 9VDC 650mA
• Breadboard jumper wire 70pcs pack
• Box for Arduino
• Arduino UNO board

Customer Reviews

*** Product Information and Prices Stored: May 05, 2012 17:00:09

FEZ Connect Shield Review

FEZ Connect Shield Feature

• Ethernet Shield
• 8 JST connectors that accepts 3-pin E-Blocks.
• 2 standard Servo motor connectors with separate power input option.
• 7 indication LEDs (power, Ethernet traffic, speed and connection status)
• Arduino compatible Male/Female Connectors for easier stackability.

FEZ Connect Shield Overview

This shield is perfect to connect your FEZ to the outer world. The "Internet of things" and physical computing has never been easier before. It supports: Ethernet* 8 JST connectors that accepts 3-pin E-Blocks. 2 standard Servo motor connectors with separate power input option. 0.22 F supper cap that feeds FEZ Domino's or FEZ Panda II's Real Time Clock when the power is off. Reset button. Programmable LED connected Di8. 7 indication LEDs (power, Ethernet traffic, speed and connection status). Jumper to choose the VCC source (5V or 3.3V) at An3 and An2 JST connectors. 5 Volt Regulator (to make it compatible with Arduino). Arduino compatible Male/Female Connectors for easier stackability. *USBizi, which is the core processor of FEZ Domino and FEZ Panda, supports the core chipset natively (WIZnet W5100) exposing a standard .NET sockets style user interface. This means that it is very easy to make your own embedded Server/Client, using TCP or UDP sockets with up to 500Kbps speed. Also, the DNS support to query websites' IP addresses and DHCP to automatic IP address leasing are supported.

Available at Amazon

Related Products

• Wall Adapter Power Supply - 9VDC 650mA
• FEZ Panda II
• FEZ Touch
• GHI 3-Pin eblock Relay
• BB400 Solderless Plug-in BreadBoard, 400 tie-points, 4 power rails, 3.3 x 2.1 x 0.3in (84 x 54 x 9mm)

Customer Reviews

*** Product Information and Prices Stored: May 04, 2012 16:45:08

Arduino USB to Serial Converter / Adapter Board Review

Arduino USB to Serial Converter / Adapter Board Overview

This board converts a USB connection into a serial (5V TX and RX) that you can connect straight to the Arduino Mini or other microcontrollers, allowing them to talk to the computer.

It features the Atmega8U2 programmed as a USB-to-serial converter, the same chip found on the Arduino Uno. The USB Serial module has an ISCP interface, allowing you to reprogram the chip when placed in DFU mode.

The pinouts on the connector are compatible with a standard FTDI header.
The USB connector is an USB Mini Connector. Supplied without cable.

Available at Amazon

Related Products

• Wall Adapter Power Supply - 9VDC 650mA
• Arduino UNO board
• Arduino Ethernet Shield
• Arduino Ethernet
• Arduino Ethernet with Power-over-Ethernet (PoE) Module

Customer Reviews

*** Product Information and Prices Stored: May 03, 2012 16:15:07

NEW PLC Programming Cable For Mitsubishi Q Series Programming Cable QC30R2 Review

NEW PLC Programming Cable For Mitsubishi Q Series Programming Cable QC30R2 Feature

• This is a replacement for Mitsubishi Q series PLC programming cable QC30R2
• Same functions with bargain price!

NEW PLC Programming Cable For Mitsubishi Q Series Programming Cable QC30R2 Overview

This professional made cable directly from industrial automation factory has all the exact same functions as the the original one and perfectly meets your need to communicate between PLC and PC.

Only a fraction of the cost for the industrial product you want.

The quality is guaranteed. It's tested before shipment.

Available at Amazon

Related Products

Customer Reviews

*** Product Information and Prices Stored: May 02, 2012 15:15:08